In order to view PDF files on this Web site, you will need Adobe Acrobat Reader. If you do not have the Acrobat Reader, you can download  Acrobat Reader for free at the Adobe web site.

 
 

1.9/3.3kV
Heavy Duty (HD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Light Duty(LD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
 
3.8/6.6kV
Heavy Duty (HD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Light Duty(LD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
 
6.35/11kV
Heavy Duty (HD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Light Duty(LD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Copper Tape Screen (CTS)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
 
12.7/22kV
Heavy Duty (HD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Light Duty(LD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
Copper Tape Screen (CTS)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Copper, Armoured
3C, Aluminium, Unarmoured
3C, Aluminium, Armoured
 
19/33kV
Heavy Duty (HD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Aluminium, Unarmoured
Light Duty(LD)
1C, Copper
1C, Aluminium
3C, Copper, Unarmoured
3C, Aluminium, Unarmoured
 
Submersible
3C, 3.3-33kV
Triplex
3.3-33kV
Termite Protection
1-33kV

General Cable have been manufacturing medium voltage XLPE cables for 25 years. We offer products compliant with AS/NZS4026, AS/NZS1429, BS6622, IEC60502 and designed to operate at the following system voltages: 

1900/3300V 
6350/11000V 
12700/22000V  		3800/6600V 
8750/15000V 
19000/33000V 
CONDUCTORS:

Generally Plain Annealed Copper (PAC) and Aluminium (AL) conductors are used for most applications, but Tinned Annealed Copper (TAC) can also be supplied where additional protection from corrosion is required. All conductors supplied are circular compacted and then covered with a carbon loaded conducting compound to ensure a smooth circular surface, thereby minimising electrical stresses on the insulation material.

Water blocking of the conductors can also be designed into products. This
is achieved by incorporating water swellable tapes that contain a swellable powder in between the strands of the conductor. On contact with moisture the powder absorbs the water, swells and forms a gel. The gel fills the interstices of the conductor and acts as a waterblock restricting the water ingress into the conductor. The tapes contain synthetic super-absorbent polymers, which give the optimal combination of a quick swelling reaction and good blocking properties. The water penetration into the conductor is restricted to a very short length that remains constant with time, heat or loading cycles. 

INSULATION:

General Cable uses Monosil technology for MV-XLPE manufacture. The silane crosslinking process involves either a copolymerisation process in the reactor, or a grafting process during extrusion between polyethylene and a trifunctional vinyl silane. The final crosslinking is achieved by immersing the insulation in water at 80 degrees centigrade, where a hydroloysis reaction initially occurs within the vinyl silane. This is followed by a condensation reaction between the hydrolysed silane groups in adjacent polyethylene chains, giving rise to a crosslinked structure. Note that a Monosil cure can still be considered a dry cure as the resulting water content of the insulation is < 250ppm compared to typical CV dry cure water content of 200ppm. 

General Cable only use water tree retardant insulation materials on MV-XLPE cables, which have passed tests in accordance with Clause 5.4.8 of Harmonization Document HD605. S1/S1:1996 Option A. 

SCREENING:

Both copper wire and copper tape screens are offered as design options. As copper is an expensive material, it is common to design the screen to match specific installation requirements. The following technical datasheets offer two screen options labelled as light or heavy duty. These are defined as 

* Light Duty can safely withstand 13.1 kA for 0.04 second. 
* Heavy Duty can safely withstand 13.1 kA for 1 second. 

Where the installation protection system and magnitude of potential earth faults are known, please contact a company representative so that we can have the opportunity to design and offer the most cost-effective solution. 

While tape screens are offered, we do not advise their use on systems greater than 11kV. Swelling of the cable core during extreme fault conditions may be sufficient to tear the tape and render it in-operable, and sufficient system protection must be installed to prevent overloading the cable.
Water blocking of the screen is also available and is achieved using water swellable tape. This tape is thermally and chemically stable for the lifetime of the cable and will withstand the temperature extremes of fault conditions. Water ingress through a sheath or termination is prevented from travelling longitudinally, and damage such as corrosion, water treeing etc is limited to the point of water entry.

MECHANICAL PROTECTION:

Aluminium Wire Armour (AWA) and Galvanised Steel Wire (GSW) are offered as standard mechanical protection for single and three core cables respectively. Non ferromagnetic materials must be used on single core cables. As the magnetic field travels through any protection layers on single core cables laid in trefoil, a ferromagnetic material such as steel will have significant eddy current losses induced in the wires causing significant heating of the cable and subsequent de-rating of its current carrying capacity. The same principle applies when selecting cable clamps.

General Cable can also provide design services for submersible installations. Lead sheathing, toredo worm protection and additional armouring can all be designed and manufactured at the New Zealand site. 

SHEATHING:

We offer various sheathing options tailored to suit environmental and installation conditions, including polyvinyl chloride (PVC), high density polyethylene (HDPE) medium density polyethylene (MDPE), and linear low density polyethylene (LLDPE).
Halogen free, flame retardant and reduced toxicity materials can also be offered to cater for specific requirements. 

Termite protection of cables can also be offered by the inclusion of an impenetrable nylon sheath, or by the addition of special additives during the manufacturing process. 

INSTALLATION: 

Cables should never be bent to a small radius. The prescribed minimums on the following datasheets should be considered the exception rather than the rule and the actual bending radius the largest which circumstances will permit. A cable must also not be laid or otherwise bent when it is at such a low temperature that damage might be caused to the insulation or serving. Where environmental conditions are at or below 0�C, cable drums will require heating, or drums stored on a site with a higher ambient temperature and moved and installed as quickly as possible before significant cooling can take place. 

 

 

Copyright  2004 General Cable Australia Pty Limited